6.18: Add Arduino VENTUNO Q (QCS8300) board support

Documentation/devicetree/bindings/arm/qcom.yaml

@@ -867,6 +867,7 @@ properties:
 
       - items:
           - enum:
+              - arduino,monza
               - qcom,monaco-ac-evk
               - qcom,monaco-evk
               - qcom,qcs8300-ride

Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml

@@ -28,7 +28,9 @@ properties:
       - ti,ina228
       - ti,ina230
       - ti,ina231
+      - ti,ina232
       - ti,ina233
+      - ti,ina234
       - ti,ina237
       - ti,ina238
       - ti,ina260
@@ -113,6 +115,8 @@ allOf:
               - ti,ina228
               - ti,ina230
               - ti,ina231
+              - ti,ina232
+              - ti,ina234
               - ti,ina237
               - ti,ina238
               - ti,ina260
@@ -134,6 +138,8 @@ allOf:
               - ti,ina226
               - ti,ina230
               - ti,ina231
+              - ti,ina232
+              - ti,ina234
               - ti,ina260
               - ti,ina700
               - ti,ina780

Documentation/devicetree/bindings/pinctrl/qcom,sm8450-lpass-lpi-pinctrl.yaml

@@ -15,7 +15,13 @@ description:
 
 properties:
   compatible:
-    const: qcom,sm8450-lpass-lpi-pinctrl
+    oneOf:
+      - const: qcom,sm8450-lpass-lpi-pinctrl
+      - items:
+          - enum:
+              - qcom,qcs8300-lpass-lpi-pinctrl
+              - qcom,sa8775p-lpass-lpi-pinctrl
+          - const: qcom,sm8450-lpass-lpi-pinctrl
 
   reg:
     items:

Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml

@@ -126,13 +126,16 @@ patternProperties:
             reg:
               contains:
                 # MI2S DAI ID range PRIMARY_MI2S_RX - QUATERNARY_MI2S_TX and
-                # QUINARY_MI2S_RX - QUINARY_MI2S_TX
+                # QUINARY_MI2S_RX - QUINARY_MI2S_TX and
+                # LPI_MI2S_RX_0 - LPI_MI2S_TX_6
                 items:
                   oneOf:
                     - minimum: 16
                       maximum: 23
                     - minimum: 127
                       maximum: 128
+                    - minimum: 137
+                      maximum: 152
         then:
           required:
             - qcom,sd-lines

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -154,6 +154,8 @@ patternProperties:
     description: Arctic Sand
   "^arcx,.*":
     description: arcx Inc. / Archronix Inc.
+  "^arduino,.*":
+    description: Arduino SRL
   "^argon40,.*":
     description: Argon 40 Technologies Limited
   "^ariaboard,.*":

Documentation/hwmon/ina2xx.rst

@@ -74,6 +74,16 @@ Supported chips:
 	       https://us1.silergy.com/
 
 
+  * Texas Instruments INA234
+
+    Prefix: 'ina234'
+
+    Addresses: I2C 0x40 - 0x43
+
+    Datasheet: Publicly available at the Texas Instruments website
+
+	       https://www.ti.com/
+
 Author: Lothar Felten <lothar.felten@gmail.com>
 
 Description
@@ -89,7 +99,7 @@ interface. The INA220 monitors both shunt drop and supply voltage.
 The INA226 is a current shunt and power monitor with an I2C interface.
 The INA226 monitors both a shunt voltage drop and bus supply voltage.
 
-INA230 and INA231 are high or low side current shunt and power monitors
+INA230, INA231, and INA234 are high or low side current shunt and power monitors
 with an I2C interface. The chips monitor both a shunt voltage drop and
 bus supply voltage.
 
@@ -124,8 +134,17 @@ power1_input		Power(uW) measurement channel
 shunt_resistor		Shunt resistance(uOhm) channel (not for ina260)
 ======================= ===============================================
 
-Additional sysfs entries for ina226, ina230, ina231, ina260, and sy24655
-------------------------------------------------------------------------
+Additional sysfs entries
+------------------------
+
+Additional entries are available for the following chips:
+
+  * ina226
+  * ina230
+  * ina231
+  * ina234
+  * ina260
+  * sy24655
 
 ======================= ====================================================
 curr1_lcrit		Critical low current

arch/arm64/boot/dts/qcom/Makefile

@@ -62,6 +62,7 @@ lemans-evk-ifp-mezzanine-dtbs	:= lemans-evk.dtb lemans-evk-ifp-mezzanine.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= lemans-evk-ifp-mezzanine.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= lemans-evk-ifp-mezzanine.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= monaco-arduino-monza.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-ac-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= monaco-evk.dtb